Select the boot menu item Original Shadow Drive to boot into the original operating system. This brings the server back into production. To fix the mirroring so that you can use the new disk-0 as your primary operating system drive and again be in a fault tolerant environment, continue with the following steps. While booted into the shadow drive disk-1 , you must "remove" the broken mirror, and then delete the missing disk. You can do this with either the Disk Management console or the Diskpart.
If there were additional volumes on the original failed dynamic disk-0, they must also be deleted before you are permitted to delete the missing disk. Select the mirror volume volume , and then view the details to see what missing disk m you need to break the mirror from. In this example, you are working with volume 0 on missing disk m0. Break the mirror by specifying the missing disk m0 , and then use the no keep option to remove the plex partition from the missing disk.
List the volumes to make sure the mirror is gone and the volume is now listed as a simple volume. Delete the new Windows Server operating system partition on disk-0, because it is no longer required. This makes room to re-mirror back to disk Convert disk-0 to Dynamic, and then select the operating system volume on disk-1 and re-establish the mirror back to disk This puts the computer back into a fault tolerant environment, and after the mirror is healthy you can boot back into disk-0 with the new boot option that was automatically added to the NVRAM.
Wait for the mirror status to become healthy. You can use the list volume command repeatedly until the status changes from Rebuild to Healthy. Quit the Diskpart utility.
This concludes this procedure and the remaining boot entries in the boot menu are all valid boot entries to boot to both the primary and shadow drives. Skip to main content. This browser is no longer supported. Download Microsoft Edge More info. Contents Exit focus mode. Please rate your experience Yes No. Any additional feedback? Note The disk that you select must not contain any data partitions and must be a raw basic disk with only unallocated space of equal or greater capacity than the primary system disk.
The following are the commands that you type at the command prompt. Note If you show more than one partition at this point, you have either selected the wrong drive, or you did not start with a raw drive. Yes, the partition that it is pointing to is the active partition. Both boot. I think something is wrong with my master boot record. But in any case here are a couple hints to look at: 1. They are SCSI hard drives. I think the article will help greatly.
If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem. Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. Please note: Do not post advertisements, offensive material, profanity, or personal attacks. Installation DVD as a physical disk.
Image file of the installation DVD, or an installation tree, which is a complete copy of the directories and files on the installation DVD. Installation tree, which is a complete copy of the directories and files on the installation DVD. You can use the inst. These repositories are only used during the installation process; they are not installed on the installed system.
Looks for the installable tree at a given NFS path. A colon is required after the host. Looks for the installable tree at the given location in the installation environment. To use this option, the repository must be mounted before the installation program attempts to load the available software groups. The benefit of this option is that you can have multiple repositories on one bootable ISO, and you can install both the main repository and additional repositories from the ISO.
This installation method requires an ISO with a valid installable tree. This option expects the path to a directory that contains a valid. If the. When the inst. Use this option when you want to manually specify the installation source in the installation program at a later time. If you want to specify an installation source, use the inst. By default, the inst.
If you modify the default label of the file system that contains the runtime image, or if you use a customized procedure to boot the installation system, verify that the inst.
For example, if your remote installation source is using self-signed SSL certificates, the inst. Example when specifying the source using inst. For example:. Disables the ability to save the output Kickstart results generated by the installation program. This section contains information about commonly used network boot options. Initial network initialization is handled by dracut. For a complete list, see the dracut. To configure multiple interfaces, you can use the ip option multiple times, once for each interface; to do so, you must use the rd.
Alternatively, you can use the ip option once, and then use Kickstart to set up further interfaces. This option accepts several different formats. The following tables contain information about the most common options. The method automatic configuration of a specific interface with an override brings up the interface using the specified method of automatic configuration, such as dhcp , but overrides the automatically-obtained IP address, gateway, netmask, host name or other specified parameters.
All parameters are optional, so specify only the parameters that you want to override. The method parameter can be any of the following:. You can use this option multiple times. However, an IPv6 address does not work with square brackets. This configures a VLAN device named vlan5 on the enp0s1 interface. The name can take the following forms:. Replace name with the bonding device name, interfaces with a comma-separated list of physical Ethernet interfaces, and options with a comma-separated list of bonding options.
For a list of available options, execute the modinfo bonding command. Replace name with the desired name of the team device and interfaces with a comma-separated list of physical Ethernet devices to be used as underlying interfaces in the team device. Replace name with the desired name of the bridge device and interfaces with a comma-separated list of physical Ethernet devices to be used as underlying interfaces in the bridge device.
This section contains information about configuring boot options for your console, monitor display, and keyboard. Geolocation is used to preset the language and time zone, and uses the following syntax: inst. The value can be any of the following parameters:. If you do not specify the inst. However, the memory dump file cannot be written to the remaining system disk in the mirror.
You must schedule a system restart for the memory dump file to be written to the remaining hard disk. On the View menu, point to Top, and then click Disk List. In the right pane, the attributes of each disk in the system are displayed. At the bottom of the right pane, a color-coded graphical view of the disks on the system is displayed:. Any disks that you are upgrading must contain at least 1 megabyte MB of free space at the end of the disk for the upgrade to succeed.
Disk Management automatically reserves this free space when it creates partitions or volumes on a disk, but disks with partitions or volumes that are created by other operating systems may not have this free space available. You must be logged on as an administrator or a member of the Administrators group to complete this procedure.
0コメント